Monday, June 13, 2011

Amy's Ant -- By Jack Dennis -- Step by step

This week is going to be step by step week. Everyday this week I will post a step by step of some of my favorite flies I tie. This fly was designed by Jack Dennis.  Named after his daughter and is a slayer on the Teton river and the South Fork of the Snake river. It is not a technical fly but has a lot of steps.

Amy's Ant

Hook:  Mustad 9672 size 6-12
Thread:  Tan 6/0
Under foam:  Tan 2mm
Top Foam:  Brown 2mm
Body: Lt. brown ice chenille
Hackle:  Brown saddle
Under wing:  Back krystal flash
Upper wing:  Elk body hair
Front body:  Peacock black dazzle dubbing
Legs:  Black round rubber legs


First step of course is to start your thread.


The first piece of foam needs to be cut like a tipless arrow. The foam should be a little smaller that the gap of the hook.


The brown foam needs a slit cut and the same size as the tan foam above.


Now tie in the tan foam with about 1/8th of an inch hanging out back. Then tie it down all the way to the eye of the hook.


Next tie in the brown foam the same length as the tan.


Side view of the tie in.


Now tie in one set of legs on each side.


Like a lot of my foam flies I need to hold back the materials that are hanging. I use a piece of scrap lead wire and wrap it around the hook tip and materials.


Tie in the hackle and then the ice chenille.


Wrap the brown chenille.  Leave about 1/4th of the shank bare.


Wrap the hackle and tie off at the same point.
Now clip the hackle close to the body.


Here is a public service announcement.  Ever have problems getting your krystal flash out?  Just make a slit in it and use your whip finisher hooks and pull a couple pieces out a time.


Pull the brown strip of foam over and tie it to the eye of the hook.  Cover the remainder shank with thread. Tie in about 10 pieces of your black krystal flash. Make sure it splays out a little.


splayed out krystal flash.


Take a generous amount of elk hair and tie it in a little longer than the tail. This shows shorter but try and hold that and the camera and having the shakes.  It is rough lol


Tie that wing in and make sure o wrap a little into the butts to anchor it down.


Cut the tips and make sure you cover all the tips with your thread.


Now with your dazzle dubbing, dub the empty spot. Dub to the end of the elk hair towards the back of the fly.






Now fold back the brown foam where the thread lays and tie the foam down.


Tie in your last set of rubber legs at that point. Tie off your thread and the tying is done. 


This is the bottom of the fly


Cut the brown and tan foam in the front as below. Of course this serves no purpose but I like to do it.






Thanks everyone for viewing

19 comments:

  1. Nice tie. I'll try it, but I don't know if these hands have that kind of skill. By the way, the rod went out in the mail this morning. Look for a long green Orvis tube in two days.

    ReplyDelete
  2. Haven't attempted an ant before...I'll have to try soon. These look awesome. And YAY rod!!! Dustin's going to be able to fish!!!

    ReplyDelete
  3. WWWWWWWWWWWWOOOOOOOOOOOOOOOOOOOHHHHHHHHHHHHHHHHHHHHHHOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOO..!!

    @ erin -- Granted this is far from an ant but it is fun to tie. This was butchered when it goes to materials and colors but I used what I had and you can use what you have as well

    ReplyDelete
  4. Really nice flies. Will try & tie a few. Enjoy the rod!

    ReplyDelete
  5. I highly recommend Bill Skilton's foam bug kits. You can usually find them on ebay or go to his site. Ants, beetles that are killer.

    ReplyDelete
  6. Good looking flies , I bet they'd pass pretty well for some of those 13 year cicadas that are so thick around the midwest this year. I hear the trout and smallmouth are having a feast on them....Jeff

    ReplyDelete
  7. nice looking hopper! Will be prime hopper season here in Iowa pretty soon.

    ReplyDelete
  8. Wow Dustin that's a nice tie!

    ReplyDelete
  9. WOw great step by step. Those flies look like they would be killing the streams around here in a week or two. Thanks again for the great flies. Peace.

    ReplyDelete
  10. This fly is awesome! It was a killer during the 'hopper hatch' last year. Great post!

    ReplyDelete
  11. OMG, they're CUTE!!! (sorry, i'm not a fisherperson but i appreciate their lifelike qualities!) you're obviously very talented in the fly world!

    (but i got some jam too!!!)

    ReplyDelete
  12. @ Howard -- I checked those out and I need to get me some!

    @ Phillip -- Let me know how they work.. I am stocked I can finally post some fishing pics.

    @ Jeff -- We have cicada's really thick here in vegas so we will see how they work.

    @ John -- I don't know how the hopper season is here yet but I have a lot to throw to the fish to find out.

    @ Jeff -- Thanks buddy!

    @ Trout -- I always enjoy your imput on my patterns and it is greatly appreciated.

    @ gofisch -- Awesome to hear it is a working pattern and excited to see how it works here.

    @ texwigirl -- Just glad you took a look at my blog and I appreciate your comment :)

    ReplyDelete
  13. well, i'm gonna follow you so i can occasionally throw in a completely un-fishing-like comment. :)

    ReplyDelete
  14. Any comments are appreciated and thanks for follower texwigirl

    ReplyDelete
  15. awesome carlos! I will be posting a step by step of a pattern I found on your blog. Of course I will give you credit for it

    ReplyDelete
  16. That's a good step by step Dustin, I'm going to tie those up for sure.

    ReplyDelete
  17. It's an awesome article for all the web visitors; they will get advantage from it I am sure.

    Feel free to visit my web page - hip to waist ratio calculator

    ReplyDelete